How to enter the settings of the Asus router (login to the admin panel). Login to the settings of Asus routers Login to Wi-Fi Asus

You try to go to the setup menu of a router, modem or optical ONT terminal via http://192.168.1.1 and the “personal account” of the device does not open for you. What to do? Call a specialist and pay money? Take your time and don't get discouraged. Let's try to figure out the problem together and decide how to log into the router?!

I think it's useful to know a little theory first:
192.168.1.1 — this is the IP address (IP) of the network device. By default, the network is usually registered on routers: 192.168.1.0/24. In other words, the local network on the router is configured with the first (lowest) address in the subnet - 1, and clients connected via the local network will use addresses with 2 By 254 . In general, this is a generally accepted rule and is configured this way for the vast majority of network devices - Zyxel Keenetic, Lincsys, Cisco, TP-Link, Upvel, Sagemcom, Asus. There are, of course, exceptions. For example, D-Link and Netgear routers use a different subnet by default - 192.168.0.0/24 and accordingly the IP will be - . But, whatever one may say, the numbers are different, but the meaning is the same - that IP 192.168.1.1, that 192.168.0.1 is the address of a network device on the network. In our case -

How to log into the router

Now let's move on to practice. To go into the settings of a WiFi router or ADSL modem, you must enter the address in the browser: http://192.168.1.1. In this case, you do not need to type the protocol at the beginning - http:// or www - the browser itself will automatically enter the required one.

If you have access to the settings, you will see an authorization form on the device, where you will need to enter your login and password (usually to log into the router via 192.168.1.1 you use: admin / admin):

This means that the local network is configured, the router is accessible and there are no problems with accessing its settings. We will consider the worst case scenario - the browser displays the error “Page is unavailable” or “Unable to access the site”:

Web interface accessibility issues can vary. Let's look at the most common of them:

Instructions on how to log in to 192.168.1.1.

Step 1. Check the activity of the network connection.

Very often, the reason for the router’s inaccessibility is the network cable disconnected from it.

In this case, it is not necessary that someone pulled out the cable intentionally - the connector can simply move a millimeter away from the network card connector and nothing will work. Be sure to check the integrity of the cable - it may be pinched somewhere or damaged by something. Please also note that the LAN cable must be connected to the LAN port of the device and not to the WAN port.

Otherwise, you will not be able to access 192.168.1.1 through the WAN port. This port is used to connect the provider cable. But only!

Step 2: Check the network indicators.

Here I mean the physical connection indicators both on the computer’s network card and on the router itself. What are they? Typically this is a green LED. If the network is active, the indicator lights up or blinks quickly. We take your device in our hands and look at the front panel. When turned on, the Power indicator must be lit - it means that the device is turned on. Then we look at the LAN port indicators - they are usually marked either simply with numbers - 1, 2, 3, 4.

When plugging the patch cord into the LAN port— the indicator with the corresponding port number should light up. If it does not light up, try disconnecting the network patch cord and plugging it into the adjacent connector. If the indicator does not light up there either, try everything one by one. Did not help? Then you have The router is faulty - take it to service.

Step 3: Check your network settings.

At this stage, we need to check the settings of the network adapter - which IP is registered. To get to the network card settings on the Windows XP operating system, click the Start button and select the Network Connections section. In Windows 7 and Windows 8, press the key combination Win+R. The Launch Program window will open. Here you need to type the phrase - control panel.

The Windows Control Panel will open, where you need to find the “Network and Internet” section.

Click on it with the left mouse button. The following window will open:

Now, to open the router’s personal account via 192.168.1.1, click on the “Network and Sharing Center” link:

Select the menu item “ Properties" . The Local Area Connections properties window will open:

Select “Internet Protocol Version 4 (TCP/IPv4)” and double-click on it with the left mouse button. In most cases, IP settings are set to automatic mode:

This is how the system was initially configured. This is done in order to facilitate the connection of the computer to the network. Thanks to this, if there is a DHCP server on the network, Windows will receive an IP address, mask, gateway address and DNS from it.
But what if there is no DHCP server on the network, or it is disabled in the configuration? In this case, logging in via 192.168.1.1 to your personal account in automatic settings will not be available, since the IP will be picked up from a special Microsoft subnet - 169.x.x.x. It goes without saying that with such an address you will not have access to the WiFi router address. Therefore, to enter its configurator, you need to register the IP manually - check the “Use the following IP address” checkbox and enter the addresses as in the picture:

That is, the following should be written:
IP address - 192.168.1.2
Mask - 255.255.255.0
Gateway - 192.168.1.1
Preferred DNS server - 192.168.1.1
Alternative DNS server - 8.8.8.8
Registered, click the “OK” button for the changes to take effect. We launch the browser again and try to go into the router settings at 192.168.1.1. The router’s personal account is still inaccessible?! Well, let's move on.

Step 4. Check the Web browser.

In the Control Panel, select the “Network and Internet” section :

Now you need to select “Internet Options” and open the “Connections” tab. Click the “Network Settings” button:

No Proxy servers should be registered.

Keep in mind that a web browser is also a program and may not work entirely correctly. Therefore, be sure to install another browser - Firefox, Opera or Chrome - and try to log into the router via 192.168.1.1 (Zyxel Keenetic, TP-Link, ASUS, etc.).

Step 5. The node can be blocked by the Security System.

It may happen that your modem or router becomes unavailable locally due to incorrect configuration of the Windows Firewall or another firewall you have installed. To eliminate this we do this:
We completely disable (by stopping the service) the security system you have installed - antivirus, firewall, etc.
Also, to exclude all options, we try to disable the standard Windows Firewall. It can also block IP 192.168.1.1 or an entire subnet. Go to the Control Panel, select the “Windows Firewall” section and completely deactivate the packet filter by clicking on the “Turn off” value.

On Windows 7 and Windows 10 Toolbars We look for the “Security System” -> “Windows Firewall” section and select the “Turn Windows Firewall on or off” menu item.

We disable it completely for private and public networks.

Again we check access via 192.168.1.1 to the personal account of the modem or router.

If none of the above helped you, then only the following scenarios remain:

1 option- The IP address on the router has been changed. That is, it is not 192.168.1.1 that is used, but another IP - 192.168.0.1, 10.90.90.90, etc. In this case, all that remains is to reset the device configuration parameters using the “Reset” button on the back panel of the device and configure it again.

Option 2- viruses and malware. Nowadays there are a lot of different infections circulating on the Internet, including viruses for routers that change some of their settings, after which logging into the device’s web interface also becomes quite problematic. Start by checking your computer or laptop for viruses.

Option 3— check if you can access 192.168.1.1 from a phone or tablet by connecting to a WiFi network. The password for connecting to a wireless network is often written on a sticker glued to the bottom of the device. If not, then, as an option, you can try using the WPS function. In this case, the PIN code will also be written on the sticker.

Option 4- Hardware failure of your modem or router. In this case, the only way out is to take it to a service center.

Video tutorial:

In this case, only 2 options are possible:
1 - Reset the settings with the “Reset” button, as described above, after which access to the modem settings should be possible without problems. But please note that after resetting the settings, the router will be pristine and will have to be completely configured from scratch.
2 - Look for the person who originally set up your device and ask for the password. If this was done by a master installer from the provider, then perhaps he installs the same thing on all devices. If the parameter settings were made by someone else, then he is unlikely to remember and will still have to use “Reset”.

The most popular devices using the address 192.168.1.1:

Zyxel equipment.

ADSL modems:

OMNI ADSL LAN EE, OMNI ADSL LAN EE, OMNI ADSL WLAN EE, P-660H EE, P-660HT EE, P-660HTW EE, P-660HW EE, P-660R EE, P-660RT EE, P-660RU EE, P-662H EE, P-662HW EE, P-741, P-791R v2, P-792H EE, P-792H v2, P-793H, P-793H v2, P-794M, P-841, P-844 EE , P-870H-51A V2, P-870HW-51, P-870HW-51A V2,
P-870MH-C1, P-871 EE, P-871M, P-872H, P-872HA, P660HN EE, P660HN Lite EE, P660HT2 EE, P660HT3 EE, P660HTN EE, P660HTW2 EE, P660RT2 EE, P660RT3 EE, P660RU2 EE , P660RU3EE

WiFi routers:

BG318S EE, NBG334W EE, NBG460N EE, P-330W EE, P-334 EE.Keenetic, Keenetic 4G, Keenetic 4G II, Keenetic Giga, Keenetic Giga II, Keenetic II, Keenetic Lite, Keenetic Lite II, Keenetic Omni, Keenetic Start , Keenetic Ultra.Keenetic 4G II, Keenetic Giga II, Keenetic II, Keenetic Lite II, Keenetic Omni, Keenetic Start, Keenetic Viva, Keenetic Extra, Keenetic Extra 2, Keenetic DSL.

(Second generation kineticists have the hostname my.keenetic.net)

D-Link equipment:

DSL-2640U B1A T3A, DSL-2640U BRU C, DSL-2640U BRU C2, DSL-2640U BRU CB, DSL-2640U BRU D, DSL-2640U RA U1A, DSL-2740U BRU C2, DSL-2750U B1A T2A

Tp-Link equipment

The configuration interface for devices from this manufacturer looks like this:

ADSL modems:

TD-W8901N, TD-W8950ND, TD-W8951NB, TD-W8951ND, TD-W8960N, TD-W8961NB, TD-W8961ND, TD-W8968, TD-W8970

Wi-Fi routers:

TL-WA701ND, TL-WA730RE, TL-WA750RE, TL-WN7200ND, TL-WN721N, TL-WN721NC, TL-WN722N, TL-WN722NC, TL-WN723N, TL-WN725N, TL-WN727N, TL-WN751N, TL- WN751ND, TL-WN781ND, TL-WR702N, TL-WR720N, TL-WR740N, TL-WR741ND, TL-WR743ND, TL-WA830RE, TL-WA850RE, TL-WA901ND, TL-WN8200ND, TL-WN821N, TL-WN821NC, TL-WN822N, TL-WN823N, TL-WN851ND, TL-WN881ND, TL-WN951N, TL-WR1042ND, TL-WR1043ND, TL-WR841HP, TL-WR841N, TL-WR841ND, TL-WR842ND, TL-WR940N, TL- WR941ND, TL-WA5210G, TL-WA7510N, TL-WR743ND, TL-WR843ND, TL-WA5210G, TL-WN310G, Acher C2, Acher C7, Acher C9, Acher C20, Acher C50.

Domain names are also used: tplinklogin.net, tplinkwifi.net, tplinkmodem.net.

Asus equipment

Web interface of older routers:

ADSL modems:

D6300, D6200, DGND3700, DGND3300v2, JDGN1000

Netgear routers:

R6300, 6200, WNDR4700, WNDR4500, WNDR4500, WNDR4300, WNDR4000, WNDR3800, WNDRMACv2, WNR3500L, WNR3500Lv2, JNR321, WNR2200, JWNR2000, JWNR2000v2, WNR1000v2 , JNR1010, WNR612v3, WNR612v2.

The more people use broadband Internet access, the more often the question arises - how to access the Wi-Fi router settings?! Many people even know that IP is used to enter the router settings 192.168.1.1 , or less often - . And yet, with access to the web configurator, some incomprehensible stories constantly arise, forcing the user to surf the Internet in search of an answer - how to log in to 192.168.1.1 to configure the router. This instruction will fully answer all your questions and will help you understand all the basic intricacies associated with accessing the configuration parameters of a wireless router.

What we're going to talk? To begin with, I will conduct a small educational program and tell you briefly what these addresses 192.168.0.1 and 192.168.1.1 are, why they are needed on the home network, where they need to be entered to go to the page with the router settings and what to do if this can't do it?!

Most often, such questions are of interest to those who have just connected to the Internet, bought a Wi-Fi router for this, and then don’t know what to do with all this stuff! The way modern network devices are designed is that before you put it on the network, you need to change the basic configuration parameters to those recommended by the provider to which you are connected. You will also have to open the router settings if the Internet stops working due to the settings being lost, or when you need to change the WiFi password or some other options. Moreover, no matter what router you use - Asus, Zyxel Keenetic, Tp-Link, D-Link, NetGear, Trendnet, Tenda, Linksys or something else - the process of logging into the router’s web interface via IP address 192.168.1.1 (or any other) is almost the same everywhere and is no different!

IP 192.168.1.1 - what is this address and how to use it

Any modern Internet access device, be it an ADSL modem, WiFi router or xPON optical terminal, is a whole mini-computer! It has its own processor and RAM, and is controlled by a special operating system. Therefore, you should not be surprised by such an abundance of various settings and functions that modern routers are endowed with. Two networks are usually connected to this mini-computer:

1. WAN or Wide Area Network- This is an external network that comes with the provider's cable.
2. LAN or Local Area Network- this is your home network, which will include a computer, laptop, phones, tablets and Smart TV.

So 192.168.1.1 is the IP address of the router on the local network, using which you can enter its settings. The same IP is the gateway for the home network.

Recently, manufacturers have begun to assign domain names on the local network to ordinary home Wi-Fi routers. The most striking examples:

Asus - asusrouter.com TP-Link - tpinklogin.net, tplinkwifi.net or tplinkmodem.net Zyxel Keenetic - my.keenetic.net NetGear - routerlogin.net Rostelecom routers - http://rt

That is, in the address bar of your web browser, instead of the IP address 192.168.1.1, you need to enter a symbolic name and press the “Enter” button.

How to find out the IP address of a WiFi router

As I said above, to organize a home network and access management, each router has its own local IP address, through which it will be accessible to all clients. It will also be indicated as a gateway for all gadgets connected to it. How to find out the router address? Yes, very simple. We take it in our hands and turn it over. As an example, I’ll show you a sticker on the Netis DL4320 modem:

On the back of the case there will be a sticker on which all the basic information about the network device is written - manufacturer, model, serial number. Also, in a separate area, the IP address of the router will be registered - 192.168.1.1, 192.168.0.1 or some other. It is this set of numbers that will need to be entered in the address bar of the browser.

If instead of IP a symbolic address is registered, then you will have to enter it. Example - TP-Link TL-MR4320 WiFi router:

By the way, the login and password for logging into the router via 192.168.1.1 are written there. Typically this is the username − admin and password - admin.

If there is suddenly no sticker on the device, then use the instructions from the manufacturer.

How to enter 192.168.1.1 into the router settings

Let's take a step-by-step look at how to properly connect and log into the router settings via 192.168.1.1 for beginners!

Step 1. We start with the fact that you first need to correctly connect your computer or laptop to it, using which we will further configure the router:

It is best to do this through the supplied LAN cable. You can see the connection diagram in the figure. That is, we connect one end of it to the network card of a PC or laptop, and plug the other end into the LAN port on the router. In general, you can log in to 192.168.1.1 via WiFi, but to do this you either need to know the password for its Wi-Fi, or be able to click on . on the router, then connect within two minutes.

As soon as you connect to a network device, the Windows operating system can automatically set the connection status to “Restricted” or “No Internet access”. There is no need to be scared - this is normal. Since the device is not configured, it does not have access to the global web! This does not affect access to the web configurator!

Step 2. Launch the web browser. You can use absolutely any browser, but I would still recommend using either Google Chrome or Microsoft Edge. Alternatively, Opera will do. But with Firefox, sometimes there are problems with the layout and operation of interactive elements,

Step 3. In the address bar where you usually write the website address, type the router’s IP address - http://192.168.1.1(or http://192.168.0.1 depending on what is indicated on its sticker). Press the “Enter” button. If everything is configured correctly and there are no problems, a window should appear with fields for entering your login and password, as in the picture above. Enter your login information to open the web interface. Typically used to log in to 192.168.1.1, login admin, password admin. Some D-Link models may not prompt you for a password. On Tenda routers, you may not be prompted for a username and password at all!

Is it difficult to configure ASUS routers? Perhaps, it is this Taiwanese company that has the graphical interface of its “native” firmware that looks as user-friendly as possible. Basic setup of such a router (RT-N of any series, WL-500 and 520, RT-G32) can be completed in 2 minutes. But first, you need to find out the address of the ASUS router in order to enter the web interface. The standard address value for ASUS devices is the following: 192.168.1.1. This is true even for routers with a built-in ADSL block. Indeed, why change anything if the standard values ​​are given in any setup manual? The standard login and password for entering the interface is the “admin” pair.

The only case when problems may arise is if someone has already “configured” the router, and did it in such a way that the value of the IP address and password became different.

Therefore, the first piece of advice. If the router is not new, turn on the power, wait a minute, press reset on its case. The reset button must be held for 10-15 seconds, then released and turned off the device. True, ASUS has a button called restore.

Asus router (red button – restore)

Now we will look at how to connect the router to a computer, and then go to the web interface.

Preliminary steps before setting up

Connecting the router's wired connections

To configure the router, you need to connect it to the computer with a network cable. The sequence of actions before setting up is as follows:

• To the WAN port (blue) - you need to connect the connector of the provider cable
• Any LAN port – connect to the Ethernet port of the computer’s network card (using the patch cord included in the kit)

ASUS router hardware connections

• Before turning on the router, it is recommended to check that the wired connection is configured correctly on your computer

An example of correctly setting up a PC network card

• If all of the above is done, you can turn on the power to the router. And send the computer to reboot.

We will configure the router from the GUI. Now let's look at how to find out the IP address of the interface yourself.

When the connection between the computer and the router is established, you can right-click on the icon for this connection. Next, select the word “Status” and go to the “Support” tab:

Connection Status - Support

In the first line of this tab, the user sees the IP address of the computer (the address looks like 192.168.1.XX). Well, the “IP” of the router ends with “one”.

For example, if the computer is assigned the address 192.168.1.13, then the web interface of the router can be opened by going to the following address: 192.168.1.1.

Although in most cases the IP address of an ASUS router is 192.168.1.1, we have looked at a universal method here (allowing you to find out its value). Let's move on to the settings.

Login to the web interface

When the router boots up (which will happen 40 seconds after turning on), the computer will establish a connection with it. Next, you can open any browser and go to the address whose meaning we found out: 192.168.1.1.

Entering the device setup interface

The router will ask the user for a login and password. The pair “admin” is suitable here. After 2-3 seconds the user will see the following tab:

Interface start tab

On the start tab, you can only configure the wireless network (change the SSID name, set a password). Internet connection settings are hidden in another tab, “Advanced Settings” -> “WAN”.

Change the settings to suit your needs

Changing the password for the web interface

For some reason, it is this option that usually raises questions. Username and password can be changed in routers, but with some restrictions. For ASUS, for example, the user name, that is, the login, cannot be changed (it always remains “admin”).

To set a new password value, in the router’s web interface go to the “Additional settings” -> “Administration” tab (then to the “System” tab):

Setting a password

Set the top field to the password value. Confirm it in the next field. Click Apply. Next time, you will only be able to access the web interface with a new password.

Happy setup!

Changing the router's IP address on the local network

If the default address value is not suitable for the user at the moment, this can be corrected. Go to the “Advanced settings” -> “LAN” tab:

ASUS router IP address (from our example) will change to 192.168.10.1. What happens after you click the Apply button.

It is important to know! Unnecessarily, there is no need to change the value of the network mask (let the mask with the last zero remain, as done “by default”).

An IP value ending in two units may be “not suitable” for the following reasons. Let's say the WAN port of the router is connected to a modem (configured in router mode). With this connection, the router is configured “for DHCP”. Then, it is imperative to fulfill the condition that the IP addresses of the local networks of the router and modem are not from the same range.

Or, let’s say, “behind the router” there is the next device, which also organizes a local network with a similar range of addresses. Changing the IP address in the router solves such problems in one second.

The video shows an example of setting up a connection “under PPPoE” with enabling the IPTV option for the set-top box:

To set up an ASUS router, you need to connect. Then, in your browser, follow the link - 192.168.1.1 . If you have not configured the device before, you will see Quick Setup Wizard. If you need a login and password, then in both fields by default we type admin(should be checked with providers). The ASUS control panel will be displayed.

basic settings

The panel consists of general and additional settings. Available opportunity viewing the network map, enabling guest Internet, traffic control, and parental controls. In the additional section Wi-Fi is regulated and configured firewall.

To check if you are connected, you can go to the “ Quick network setup" Then select " Check your connection" And " Go" In the window that appears, enter your username and password. Click " Further" Then in the section " Setting up the router» fill in the specified name (SSID) and network key (to connect to the network).

Click " Apply" Will begin . Then a network with the name you specified will appear in the Wi-Fi list. We connect to the device using the specified access key and return to this section. In the window with connection information, click “ Further».

In most cases, the Internet should already be working, but if your provider does not support the technology AutoIP, That tune Wi-Fi follows on its own. In this case, after checking the connection, the section “ Internet Settings».

Next in the proposed list choose the connection technology used by your provider. Then in the window that appears you will need to enter login And password, which were provided by the provider in the contract. All information should be clarified with him if any problems arise. It may be necessary further enter any other parameters that must also be taken into account (service name, IP address, etc.). Afterwards you need to do all the same steps as described above.

Wi-Fi Settings

On the main tab there is always an additional option tune Your Wi-Fi. For example, in the section " Internet" Can change type of WAN connection, that is, if the provider has changed the connection technology, you can switch it. In chapter " Network map» there is a possibility change key to connect Wi-Fi, as well as your username (be sure to click " Apply"). Can be customized guest network(not recommended if you need to control Internet traffic) and impose parental control, if required save child from an unwanted resource.

You can also change access key to the control panel of your router. To do this, go to " Administration", Further - " System" Enter your new password and click " Apply" for it to take effect. The remaining sections mainly contain additional settings for wireless and local Wi-Fi, which you can configure at your discretion.

How to reset a router

If you forgot your wireless Wi-Fi password and other devices were not connected, try logging into control Panel on cable and view it there. But if this is not possible, it is recommended reset router to default settings.

There is a special button on the back of the router for this purpose. Press and hold it about 15 seconds until the WPS indicator starts blinking. The access key will be reset, you must follow all the steps described in the article above. To avoid such situations, when connecting on your computer, you should always check the “ Connect automatically" Then the Wi-Fi login will be done using autofill.

In this step-by-step instructions, we will look in detail at how to configure the Asus RT-N10 Wi-Fi router in its various variants:

• RT-N10P
• RT-N10+ D1
• RT-N10E B1
• RT-N10 B1
• RT-N10 C1
• RT-N10U B

And other modifications of this popular and cheap Asus wireless router. The basic setup of the Asus RT-N10 Wi-Fi router, regardless of its modification, is the same. That is, if you need to configure the router so that it distributes wired Internet to wireless devices, you do not need to know which of these Asus RT-N10 Wi-Fi router options you have. The only possible difficulty is the new firmware 3.0.0.x on some models (black background) or 7.0.2.31 on other versions (although routers do not go on sale with this firmware), but in fact, this is not a difficulty - all the actions necessary for successful setup are completely identical. However, we will include screenshots of this firmware here.

• Preparing for setup, connecting the Wi-Fi router Asus RT-N10
• How to enter the settings of Asus RT-N10
• Setting up an L2TP Beeline connection on firmware 2.0.x, 7.0.0.x (plus setting up Beeline television)
• Setting up PPPoE connection to Rostelecom and Dom.ru on Asus RT-N10 with firmware 2.0.x (plus setting up IPTV Rostelecom)
• Setting up a wireless network, setting a Wi-Fi password on Asus
• Setting up Asus RT-N10 with new firmware
• Firmware Asus RT-N10

For novice users who have never set up routers, let me note: there is nothing complicated about this, the whole process will take no more than 15 minutes.

Preparing for setup and connecting the Asus RT-N10 router

Before setting up a Wi-Fi router, you should connect it correctly, and as experience shows, even with this there are problems. And, in addition, pay attention to some network settings that may be critical for successful setup.

First of all, it is recommended to check the settings of the local network connection that is used to configure the Asus RT-N10. In particular, the TCP/IP protocol parameters should be set to “Obtain an IP address automatically.” How to do this is written in detail (will open in a new tab).

The next point to remember: if your provider uses connections like PPPoE, L2TP, PPTP and others, that is, in order to access the Internet, after turning on the computer, you launch some kind of Beeline, Rostelecom, Dom.ru connection from the desktop or from the list of connections in the taskbar, disconnect this connection. And do not connect again either while setting up the router or after the wireless router has already been configured. Those. This connection will be established by Asus RT-N10 itself in the future; you don’t need to run anything, otherwise you will get a result in which the Internet will only be available on the computer, but not via Wi-Fi.

And now about connecting the Asus RT-N10. There are five network connectors on the back of the router. One of them stands out among the rest - connect the cable of your Internet provider to it. And connect one of the remaining ports to the corresponding port of your computer’s network card, and then turn on the power to the router. You can start setting up.

How to enter the settings of the Asus RT-N10 router

Go to router settings

To go into the settings of your Asus router, launch your browser (it's already running if you're reading this, so better open a new tab) and enter 192.168.1.1 in the address bar, after which you should see a username and password request. The standard login and password for routers from this manufacturer are admin and admin, here and there. You may be asked to change your default login information, please do so. After this, you will find yourself on the main settings page of the Asus RT-N10, which looks like this:

On this page, all operations for setting up connections, setting a password for Wi-Fi and other actions are performed, which we will now do.

Setting up Asus RT-N10 for Beeline

In order to configure an Asus router for Beeline, on the main page of the router settings, click “WAN” in the menu on the left, then fill in the parameters for the Beeline L2TP Internet connection, which look like this:

Setting up a Beeline connection on Asus RT-N10 (beeline l2tp)

Basic parameters to set:

• WAN connection type: L2TP
• Selecting an IPTV port - if you use Beeline television, select the port to which you will connect the Beeline TV set-top box.
• Obtain an IP address automatically - Yes
• Connect to DNS automatically - Yes
• Username, password - your data for Internet access from the Beeline provider
• PPTP/L2TP (VPN) server - tp.internet.beeline.ru
• Apply the settings. On some Asus firmware, settings are not saved if you do not enter anything in the “Hostname” field. Enter beeline.

If no errors were made, and the Beeline connection on the computer is broken, then after a short time the connection to the Internet will be established and all that remains is to configure the wireless connection parameters. You can make sure that the Internet is working by opening a new tab and trying to access a website. About setting up Wi-Fi on Asus, see below, after the information on setting up a router for Rostelecom and Dom.ru.

Setting up Asus RT-N10 Rostelecom and Dom.ru

In order to configure the Asus RT-N10 Wi-Fi router to work with Rostelecom and Dom.ru providers, which use PPPoE to access the Internet, follow these steps:

• In the menu on the left, select “WAN”
• Set the necessary connection parameters, the key ones being Connection type (PPPoE), automatic acquisition of an IP address and DNS (you need to set it to “Yes”), your Rostelecom or Dom.ru login and password. The remaining parameters can be left unchanged. If the settings do not save without entering anything in the Hostname field, enter rostelecom or domru. Also, if you need to set up Rostelecom IPTV, specify the port to which you will connect the TV set-top box.

Save the settings and wait a short time. The router will have to establish a connection to the Internet and if you try to access any page, it will open, despite the fact that the Rostelecom or Dom.ru connection on the computer itself is disabled. Now it is advisable to configure the wireless Wi-Fi network settings.

Setting up a wireless network and how to set a password on Wi-Fi Asus

Another of the main tasks when setting up a Wi-Fi router is setting up the parameters of the wireless network, which is necessary so that, firstly, strangers cannot connect to it, and secondly, to make it more convenient for you to use it. Setting up Wi-Fi does not depend on what provider you have - Beeline, Rostelecom or any other.

In order to configure the basic parameters of the wireless network and set a password for Wi-Fi, in the settings menu on the left, click “Wireless Network” and on the “General” tab enter the basic parameters:

• SSID (Wireless Network Name) - Enter something of your own here, so you will distinguish your network from others. It is better to use the Latin alphabet, otherwise some devices may have problems connecting via Wi-Fi.
• Authentication method - WPA2-Personal
• The WPA Preshared Key is your Wi-Fi password, which must be at least 8 characters long.
• You don't have to change the other parameters, especially if you don't know what they mean.

Apply the settings. Wait for a message indicating that the Wi-Fi settings have been successfully changed. And, in fact, that’s all - you can try connecting via Wi-Fi from a laptop, phone or tablet, everything should work.

Setting up the Asus RT-N10 router with new firmware

Frankly speaking, I don’t know if Wi-Fi routers with this type of firmware are on sale (in my opinion, yes, for example Asus RT-N10P and RT-N10U), but it can be downloaded and installed on some models of the RT-N10 router . The firmware index is 3.0.0.x and the web interface of the router with this firmware version looks like this:

As you can see, despite the fact that the design style has changed, the location of the settings menu items remains unchanged when compared with firmware 2.0.0.x and 7.0.0.x. Therefore, the basic setup of an Asus Wi-Fi router with new firmware occurs in exactly the same way as was described above for Beeline, Rostelecom and Dom.ru.

Firmware Asus RT-N10

If you want to flash the Asus RT-N10 router, then this is not particularly difficult. First of all, you will need to download the firmware from the official website. Considering that there are quite a large number of modifications of this router, it is important not to make a mistake here. To do this, go to the router settings panel and select “Administration” in the menu on the left, then open the “Firmware Update” tab.

Pay attention to two points: Product ID and Firmware Version - this information tells you which Asus RT-N10 you have, as well as what firmware is currently installed.

At the top of the page there is a link to the firmware page, but you should not click on it - from experience, it does not always lead to the correct router model. Therefore, the best option to download firmware for an Asus router is to go to the website http://www.asus.com/ru/, select products - Network equipment - Wireless routers, then go to the page of your router model, click the “Support” link ", and then - "Download". In the “Software” group you will find all the firmware that can be downloaded and installed on the router. Download the correct firmware version, extract the firmware zip file, and return to your router's firmware update page.

Click Select New Firmware File and then Submit. Wait for the Asus router firmware to complete; it will take about three minutes, during which the connection with the router may be interrupted. When finished, you will see that the firmware version on your router has been updated.

I hope this instruction helped you. If it’s not difficult, share it on social networks using the buttons below.