Nowadays, many people work directly on the Internet; they do not necessarily have to sit in an office to conduct their business. Many problems are solved through the network, so it is extremely important that a high-quality Internet signal is available absolutely everywhere. If the dacha is located far enough from the city, plus the tower is not located nearby, then you can’t hope for high-quality Internet. But what to do in this case, not go to the country? Build a tower near you? Everything is much simpler: you just need to make an Internet signal amplifier for your dacha yourself.

A little theory

Before you find out how to make the best Internet signal booster for your dacha, you need to understand a little what 3G and 4G are, and also what can cause a bad signal.

Not so long ago, many summer residents used satellite Internet, but this technology has almost completely outlived its usefulness, but now the vast majority of people use it, which gives very good speed for comfortable work on the network. Today in Russia there are three communication formats - 2G, 3G and 4G. As reported a little earlier, in 2 years, in 2020, the most modern format will appear - 5G.

To understand how the classification of communication formats differs, you need to know the following:

• 2G, also known as EDGE, is the slowest mobile Internet, its speed does not exceed 40 Kb/s, and today it is practically not used anywhere.
• 3G is the first high-speed Internet, thanks to which you can surf pages very comfortably. The speed of this communication format does not exceed 800 Kb/s.
• 4G is the fastest mobile Internet in Russia today, its speed is 2-5 Mb/s.
• 5G - since the implementation of this format has not yet occurred, it is quite difficult to say exact numbers, but the approximate speed should be about 1 Gb/s.

These statistics are approximate, because theoretically the speed can increase at each point, it all depends on the operator’s throughput.

Mobile Internet signal amplifier for a summer residence

Each person can personally enhance the signal quality of a 4G modem, which can be purchased at any store cellular communications selected operator. To use the Internet through such a modem, you need a computer or laptop. But you should also take into account the factor of connection stability; if the operator is not able to maintain an uninterrupted signal (even at low speed), then it is rational to simply change it. Otherwise, the user will still receive a poor-quality Internet connection.

There are several possible options for how to strengthen the signal. The most popular are:

1. Extend the USB cable through which the modem is connected to the computer or laptop. Thanks to this, the modem can be placed somewhere higher or even taken outside, and the quality of communication will significantly improve.
2. UTP extender for 3 or 4G modem. A regular USB extension cable is unable to work properly if the cord length exceeds 4 meters. In this case, the extension cord can have a high-quality connection to the computer at a distance of up to 20 meters. Therefore, the modem can even be taken to the roof of the house.
3. Purchase a special Internet signal amplifier. Not the cheapest way, because the cost of a complete set will cost about 2800 rubles. ($50), however, the end result is really worth the money.
4. Make a special antenna with your own hands that will improve the quality of communication.
5. Change operator. At first glance, such a banal procedure may turn out to be the most effective.
6. Select the “3G Only” or “4G Only” mode.

We’ve sorted out the main methods for improving Internet connection, now we’ll talk about each of them in more detail.

Extend the modem via USB cable

To improve the quality of the signal, you should understand that this is a wave that spreads unevenly in different parts of the house. This means that you first need to determine where the signal is strongest and most stable. This will require a little time and patience, when this place is determined, you should proceed to the next step.

Almost all modems display the dBm value, which is what you should pay attention to. If this value is less than 70, the signal is simply excellent and this is where it is best to place an Internet access point. When the signal level is within 70-80 dBm - an average indicator, if there is no better indicator in the house, then you will not notice any strong discomfort when surfing pages. But when the dBm value is more than 100, the signal is very weak.

In practice, it is known that the strongest signal exists near windows and closer to the ceiling. It is best to place the modem somewhere near the roof. At the same time, you don’t have to worry about the device. All modems are not afraid of wind, rain and frost, but it is not advisable to expose the device where there is a lot of sunlight.

So, if the location has been determined, now you need to go to the store and simply purchase a USB extension cable of the required length. It is important to remember that if it is more than 4 meters long, then this procedure loses all meaning, the signal quality will again be poor.

UTP extender

If four meters of an extension cable is not enough to seriously improve the signal quality, then you should purchase a special UTP extension cable. Such a device can qualitatively extend the modem up to 20 meters. Therefore, if the access point needs to be placed on the roof, this is exactly what you need.

The extension cord consists of three parts:

1. A USB port that plugs into a laptop or computer.
2. The port where the modem is connected.
3. UTP cable that connects two ports. You can use a classic UTP-5E cable.

But if 20 meters of cable is not enough for you, then in this case you should purchase a more expensive one. High-quality information transmission will be stable at a distance of up to 50 meters.

for the dacha

Often in stores you can see special antennas that are designed to amplify the signal. They are purchased along with the required amount of cable; the antenna should be installed on the roof of the house.

The difficulty of installation is that one person cannot do it. Before installing the antenna, you should choose its exact direction, in which direction there will be the highest quality signal. The process goes something like this: one person slowly turns the Internet signal amplifier for the dacha, and the second on the computer looks at the dBm frequency and where the value will be the lowest, in this direction the device should be mounted.

The antenna itself is connected to the modem, and the modem, via a cable, is connected to the computer. It is also worth noting that the modem must be no further than two meters from the signal amplifier, otherwise there will be no result. There are also some other connection difficulties. Not all modems have antenna outputs, and those that do are of insufficient quality, so it is likely that you will have to resolder the input yourself. If you don’t know how to do this, then it’s better to take the modem to craftsmen who have soldered dozens of such devices.

This method is very complex and expensive; moreover, the antenna must be grounded. However, in some cases it is the antenna that becomes the savior. If the tower is located far enough (more than 10 km), then this is the only correct solution.

DIY signal booster antenna

You can use a homemade antenna not only at the dacha, but also on a hike; it’s quite simple to make. You need to wind copper wire onto the USB modem; it’s quite difficult to say how many turns you need, but there should be quite a few of them. The most wire should be wound where the SIM card is located. At the end of the wire you need to make a small screen from an ordinary tin can, and if you have an unnecessary CD, then it is generally ideal for homemade antenna. Such a simple Internet signal amplifier for a summer residence can improve the quality of communication by up to 20%, which is a very good indicator.

Second version of a homemade antenna

There is also a stationary version of the antenna. Two diamond shapes should be made from fairly thick copper wire. In appearance, the antenna should resemble an unrounded figure eight. To the place where the rhombuses meet, you should solder a regular antenna cable, wrap the other end of the cable around the modem, as indicated in the previous example. Mount the antenna with the modem on the roof of the house or place it out the window, and connect the modem to the computer when USB help or UTP extender.

Changing operator

The quality of the Internet signal directly depends on the proximity of the towers located and the quality of the equipment. Therefore, before tinkering with anything, you should try to simply change the operator, sometimes this is the simplest and most effective method of strengthening the signal.

Users' opinions

But what do they say about what it really is - the best Internet signal amplifier for a summer residence, user reviews? Of all the methods described above, people most often prefer conventional extension cords. In most cases, they are the ones who help solve the problem. Also, many people respond well to the antennas they purchased. As for homemade devices, then opinions are divided here. DIY antennas have helped some, while others complain that there was no signal improvement at all. However, we should not forget that people could simply not follow the instructions or simply do something incorrectly.

Editor's Choice

How to choose the right Internet amplifier for your dacha - TOP 7 best devices[Rating]

Using an Internet amplifier, you can significantly improve the signal quality in your country house, at home, and in any other room.

Effective devices have been on the market for a long time.

These are the so-called dilators or extenders.

Their main task is to expand the existing signal.

In rural areas or in places where the network coverage is very weak, there is no point in using an extender, since the poor quality of the Internet in this case does not depend on the router, but on the poor network of the operator.

Perhaps there are not enough towers on the territory, the connected ones have low bandwidth, or the signal is “interfered” with buildings, forests, and so on.

To solve the problem bad internet in a private home we recommend using repeaters – these are special gadgets that can increase Internet speed several times by reducing the signal-to-noise ratio.

You can improve the quality of the network using special kits to strengthen the 3G-4G signal.

Contents:

When choosing an amplifier kit, You should pay attention to the following parameters:

• Coefficient signal amplification. It is generally accepted that indicator values ​​that are 8 dB and above are the normal gain level. Such repeaters are perfect for use in areas remote from the city;
• Frequency range - This is a kind of reproducible streak. The larger it is, the more efficient the repeater will work;
• Mounting type. In order for the amplifier to be able to catch an existing tower signal, it is necessary to install its antenna as high as possible. Typically, users choose the roof of their home for installation. When purchasing a product, first decide on the type of fastening, and then select the options that suit you;
• Kit cable length . Determined by the location of all devices in the kit;
• output power (from device to base station).

Also, you should pay attention to the temperature range at which the device will operate normally.

If you live in a region characterized by frequent frosts, this indicator will be almost the main one when choosing a gadget.

When choosing an amplifier, consider your location, the approximate distance from the nearest tower to your home, and the required number of connection points. Remember that the total data transfer rate achieved by the amplifier will be shared among all.

Vegatel VT-3G

Estimated cost: 11,900 rubles.

This cellular signal amplifier is the best in terms of price/quality ratio.

Vegatel is a domestic manufacturer of equipment for enhancing communications of various types.

In Russia and other CIS countries, devices from Vegatel are in demand.

Average cost and effective work devices will solve the problem of slow Internet and cellular communications even in the most remote summer cottages.

• The amplifier is capable of picking up very weak signal;
• Easy to use;
• The control interface has been translated into Russian;
• There is an overload level indicator;
• Affordable price.

• The basic configuration does not include a bracket;
• No router.

The direction of the antenna must match the approximate position of the station being used mobile operator.

Telestone TS-GSM 1800

Estimated cost: 15,600 rubles.

Telestone is a Chinese company that deals with... The products are mainly aimed at the Russian market.

The TS-GSM 1800 repeater model is distinguished not only by its good price, but also by the ability to work with any number of subscribers.

Thanks to a gain of 70 dB, you can achieve good signal amplification without interference, even if 100 subscribers are working in the house at the same time.

It should also be noted good quality repeater assembly. The case is designed to support IP40 protection, which allows it to resist moisture, sand and other fine particles. TS-GSM 1800 is suitable for medium-sized rooms, mainly for country houses.

• Small repeater size;
• The case is protected from moisture and dirt getting inside;
• Large coverage area, suitable for any suburban area;
• Good network quality as a result of amplification;
• Unlimited number of network subscribers.

• Cables and antennas are not included in the package. All components necessary for installing the repeater can be purchased separately from the manufacturer or separately;
• The installation is difficult, because there are no exact instructions with factory components. To configure the operation of this repeater, we recommend that you contact a specialist.

The powerful repeater housing can cope with all weather conditions.

Anytone AT 6100W

Estimated cost: 37,800 rubles.

This repeater model is the most powerful of all other TOP amplifiers, however, the price of the device leaves much to be desired.

Anytone AT 6100W is more suitable for large enterprises and factories than for a summer residence.

However, if you want to provide maximum quality connections and price are not important to you, feel free to choose this model.

IN complete set devices include:

• The repeater itself is AT-6100W;
• External antenna;
• Internal antenna;
• Power adapter;
• Cable 10 m and 5 m (for external and internal antennas, respectively). If necessary, you can buy additional skeins from the manufacturer or pre-order the required quantity;
• Operating and installation instructions;
• Warranty sheet. With its help, you can exchange the amplifier kit or get your money back if the gadget turns out to be faulty.

Also, the repeater works with the UMTS communication standard (type GSM 900).

This allows the gadget to function perfectly as a modem.

To connect the Internet to a computer at the dacha, just use the Anytone AT 6100W repeater and use a smartphone, or you can work with a 3G modem.

• Reliability. Using Anytone AT 6100W, you will not encounter constant breakdowns of the antenna or other components of the kit. All parts are of the highest quality and will last for many years even in cold climates or sudden changes in weather conditions;
• User-friendly design and ease of use;
• Operates without interruption at temperatures from -25 to +55 degrees Celsius.

• High price;
• The device is intended for buildings much larger than ordinary dachas.

Vegatel VT-900E

Estimated cost: 11,900 rubles.

This repeater is similar to the leader of the TOP. The only difference is that Vegatel VT-900E does not support WiFi.

Users can boost the signal only for the cellular network.

Accordingly, at the dacha you can only use fast 3G Internet.

Also, this one from VEGATEL has a smaller coverage area than the previous model - about 650 sq. m.

• Good coverage area;
• Stable work;
• Suitable for both cottages and other large buildings;
• Price-quality ratio.

In general, the Vegatel VT-900E repeater is perfect for boosting a cellular signal in any summer cottage.

The repeater will work without problems, even if the house is located in the middle of the forest or far from the base station.

On the body of the repeater there is a button for adjusting the signal level. Also, this parameter can be adjusted automatically.

There is protection against network overload. Normal operation of the device is possible at temperatures from +25 to +55 degrees.

Picocell 900 SXB

Estimated cost: 8,200 rubles.

Picocell 900 SXB is a relatively inexpensive and high-quality repeater that works with the GSM-900 communication standard.

Great for small spaces or houses with 1-2 floors.

Allows you to amplify the incoming signal and distribute it over an area of ​​up to 200 square meters. m.

The peculiarity of this device is that the developer positions the Picocell 900 SXB repeater as a device for signal amplification in the city.

If you decide to choose this device for your dacha, it is advisable that the house is located close to the base station or to a large populated area.

• Small size;
• Acceptable price;
• Low energy consumption;
• Build quality;
• Easy to install;
• It amplifies the signal well over an area of ​​up to 150 square meters. m.

• Designed to work within the city. There is no way to amplify the signal if it is blocked by large houses or forests;
• Limitation on the number of subscribers. Up to 15 different devices can use the “enhanced” network at the same time.

REMO Orange 900 Plus

Estimated cost: 5,500 rubles.

REMO is the name of a Saratov enterprise for the development and production of electrical and radio devices.

It is not always possible to use wired Internet, for example, in a country house, in a country house, in a new office, and the mobile Internet works poorly or disappears altogether. In order not to burn your nerve cells by spending 10 minutes trying to load a video or a heavy page, you can buy an antenna amplifier. This article is dedicated to one of the modern models - HiTE HYBRID, which helps increase the speed of both 3G and 4G (LTE) Internet, does not require long settings (it took me no more than five minutes to connect) and is connected using a single cable, through which Both power supply and data transfer occur.

The HiTE HYBRID antenna amplifies the signal using MIMO technology, which significantly increases the quality and stability of the Internet connection. The declared antenna gain for 4G is 2 × 16 dBi, for 3G - 2 × 13 dBi.

In addition, the Internet can be distributed through a router: HiTE HYBRID is compatible with all routers, and you can connect it to both a PC and a router.

We tested the HiTE HYBRID antenna for 4G signal amplification and received good results not only in Internet speed, but also in the ease of installing and configuring the antenna.

By the way, since 4G Internet is still far from universal, in case of its absence, the antenna amplifies the 3G signal, and this deserves special mention.

Now and with a view to the future

Now all mobile operators are switching from 3G to the fourth generation Internet, but 4G coverage is still not available everywhere.

It turns out that if you decide to strengthen the 3G signal, you need to buy an antenna specifically for this reception frequency, and in a year or two, when the 4G coverage area reaches your area, you will have to buy a new one.

With HiTE HYBRID such troubles are eliminated. It amplifies 3G and 4G signals and selects the best, so you don't have to worry about frequencies or buying new equipment.

Equipment and configuration

In the box you will find the antenna itself and a neatly folded PoE adapter, an Ethernet cable for connection, a power adapter and a mount.

Antenna and accessories in the box

The HiTE HYBRID antenna has a durable and completely sealed housing made of metal and plastic with dimensions of 250 × 250 × 75 mm and a weight of 2 kg.

Antenna housing with waterproof connectors

Of course, it is best if the antenna is installed outside, on the roof of a building or on a bracket outside a window. In this case, maximum gain can be achieved.

Operating temperature range from -30 to + 50 °C. The manufacturer promises that operation is possible at lower temperatures if the power is not turned off in winter. The kit includes a pole mount (or bracket).

A cable 30 m long is suitable for the antenna. This is quite enough to stretch it from the house to the roof, but if you need more, you can extend it to 100 m.

As we wrote above, this cable serves both for power and data transmission, which simplifies installation even more - you don’t have to buy any adapters or extension cords. The kit already contains everything you need to operate the antenna.

Select SIM

You will need a SIM card for the antenna. If your SIM card does not support a 4G network at a frequency of 2,500–2,700, the antenna will work with a 3G network at a frequency of 1,900–2,200.

In general, the antenna will work with any Russian operator that provides mobile Internet using 3G or 4G technology. I tested the antenna with a Megafon SIM card with 4G Internet.

SIM card "Megafon" 4G

We insert the SIM card into the special slot and screw on the waterproof cover. It's sealed, so you don't have to worry about the safety of your SIM card.

We open the address specified in the instructions on the PC and see the connection management interface.

Connection management interface

You can see the connection status and statistics.

Statistics

Testing the antenna in the field

To test the speed of the antenna, I used the Speedtest.net service. To compare the speed, I took a modem from Megafon with me and tested it with the same 4G SIM card.

We decided to test the antenna in the field conditions for which it was, in fact, intended. Since I have neither a dacha nor a country house, we simply went out into nature - into the forest not far from the city (about 12 km).

Location 1. Clearing in the forest, 12 km from the city

6.21 Mbit/s - incoming speed, 1.21 Mbit/s - outgoing speed.

Modem: does not connect.

In the meadow

We assembled it according to the instructions included in the kit: we connected the antenna to the POE adapter, the adapter to the laptop and connected it to the car’s network via a converter.

Antenna connection
Connected and ready to go

I must say right away that we tested more than one place - somewhere the antenna worked better, somewhere worse. In the original location, where the modem completely refused to pick up a 4G signal, the antenna gave an incoming speed of 6.21 Mbit/s.

Location 2. On a hill, 12 km from the city

8.62 Mbit/s - incoming speed, 1.05 Mbit/s - outgoing speed.

Modem: does not connect.

The fishing was best near the car, although due to the long cable we moved around the entire clearing, trying to catch the best signal. The most successful indicator in this area is 8.62 Mbit/s (stopped on a hill).

Speedtest results in the second location

The next place was closer to the city, about 5 km, in a field.

Location 3. Field, 5 km from the city

11.95 Mbit/s - incoming speed, 0.44 Mbit/s - outgoing speed.

Modem: 0.05 Mbit/s - incoming speed, 0.05 Mbit/s - outgoing speed.

We catch a signal in the field

Here the modem from Megafon started working. It returned 0.05 Mbps (not to mention that we could barely wait for it to open the speed test at all).

With the antenna, mobile Internet from Megafon soared to 11.95 Mbit/s. In principle, these were the best results that were achieved.

General impression

If you use a 3G/4G antenna outside the city, where the Internet often disappears altogether, the performance is very different from the same modem (as can be seen in the screenshots above).

In a forest clearing 12 km from the city, we got the speed with which we can use the Internet without the risk of breaking the computer from rage.

In principle, if instead of a person who wanders through the field and forest clearings, raising the antenna above his head, there was a master who will install the antenna on the roof of the dacha, the speed would be even faster.

But, as I said above, to connect an antenna and get your legitimate 5-10 Mbit/s even on 3G, you don’t need any knowledge or skills.

So, if you have been suffering from slow mobile Internet (or lack thereof) for a long time, read detailed characteristics and you can order the antenna here↓

Hite Hybrid 3G/4G antenna

P.S. HiTE also produces more powerful 4G LTE antennas, but we chose the HYBRID model for testing for its versatility and ease of setup.

About 70% of citizens of the Russian Federation have at least once encountered the problem of poor communication quality, both in rural areas, for example, in a country house, in a village, and in an urban environment. One way or another, this is primarily due to the blocking of the signal by high-rise buildings, building ceilings, and the terrain features of the area where the services of telecom operators are used. In order to improve mobile communications in the country, many users try various tricks, for example, leaving the room to go outside, changing their position in space, or completely stopping using the services of their telecom operator. But they all solve the problem only for a while.

How to boost your cell phone signal yourself?

In order to improve communication in a country house, in an apartment, or in another type of room, you need to buy a cellular signal amplifier. This is a device that allows you to “extend” a communication signal; it is capable of converting a weak signal and increasing the speed of its reception. The characteristics of all repeaters are different. The most important of them are the coverage area, as well as the power reserve, because with the onset of a particular season, different amounts of power are required for good work.

You can buy a repeater either in a retail store or in any online store specializing in the sale of electronic and household appliances. After purchasing a router, carefully read its instructions. It is not difficult to install the purchased kit yourself if you know its composition. In the purchased box you will find:

• repeater;
• external antenna;
• antenna internal;
• cable assembly;
• adapter.

Repeater installation steps

1. First you need to install an external antenna, it will be directly responsible for receiving the signal. Deciding on the installation location is not difficult; it is important to know where the base station is located and point it in the right direction. Take out the antenna, mount it on a bracket or mast in a chosen location - this could be the facade of a building, the roof of a country house or something else. Avoid nearby structures such as fences, trees, and poles.
2. The next step is to lay the cable into the room and connect it directly to the cellular amplifier - repeater.
3. Next, connect the internal antenna to the device. Outwardly it resembles a kind of pin and has its own input connector. For correct operation of both antennas, electromagnetic isolation is required. This means that they must be installed at a sufficiently large distance from each other and, preferably, that there is at least some kind of barrier between them, for example, a cabinet or a wall.
4. If all equipment is secured correctly, you can safely connect the device to a power source.

If you encounter a problem bad connection or constantly interrupted calls at your favorite dacha, house or apartment, purchasing a repeater will help solve it.

The price of cellular amplifiers varies depending on the built-in parameters and the availability of additional options. By purchasing a signal repeater, you can improve mobile communications at your dacha with your own hands. But it is worth remembering that some models have special switches or built-in LCD displays. If you do not have sufficient knowledge and experience to connect such a device, there is a risk of damage or incorrect installation. Therefore, if you are not confident in your abilities, entrust the installation to a specialist or company engaged in the installation and optimization of cellular communication amplification systems.

Mobile communications are an integral part of our lives, leaving us far behind. Thanks to it, we can always be in touch, and at the same time have access to the Internet. However, there are situations when network coverage is not good enough, which in turn negatively affects the quality of voice calls and mobile Internet speed. This problem updated the mass introduction of 4G, the signal of which is not good in all places.

If you have poor quality cellular signal coverage at home or in your country house, then it is quite possible to solve this problem, although this will require money and time.

Feasibility of the process

Before purchasing equipment and installing it, contact the operator.

If the signal quality is poor mobile network, call the operator and report this problem. If your neighbors also encounter this, then let them contact the operator. The more applications, the greater the chance that your problem will be solved by specialists mobile operator for their corporate funds.

For its part, the operator can solve the coverage problem in two ways: installing a new base station or installing additional modules on an existing one.

In the case when the operator, for certain reasons, cannot solve the problem with the coverage, this must be resolved on its own. Before you do this, you need to calculate everything.

If the coverage of your mobile operator is of poor quality, then maybe you should give preference to another? Today, fortunately, the choice of operators mobile communications sufficient. When this option is not suitable, and you urgently need to organize high-quality and reliable coverage - let's get down to action!

Equipment and scope of work

You probably know that cellular communications are divided into 3 types (generations): GSM (2G), 3G and 4G. Each of them operates in a certain frequency range. Depending on the required amplification, the type of network will need to select equipment.

It is impossible to amplify the signal of several generations of networks at once with one set of equipment. To amplify the signal, each generation of the network needs its own separate set of equipment.

However, in most cases, only one generation of the network is needed to strengthen the signal, but which one? Everything is complicated by the fact that each of them has its own advantages, but, nevertheless, let's try to come to a common denominator.

Net

First, study the network coverage around you. If you receive a signal from a base station with 3G or 4G, then it is best to focus on this generation, since it is the latest and also allows access to high-speed mobile Internet. The main thing is that all devices support this type communications.

Tasks

The generation of the network must also be selected from the assigned tasks. If you need reliable coverage for making voice calls, but don’t need the Internet, then focus on the GSM network - it’s simple and practical.

Subscriber device support

The only caveat is that everyone must have devices that support the selected type of network. If absolutely everyone supports GSM Cell phones and smartphones, then third and fourth generation networks are not all. In other words, if you want to implement a 4G network, all household members will need to purchase devices with appropriate network support, which are by no means cheap.

In a word - it's up to you. It is better to choose a 4G network, as it provides high-quality communications and high-speed Internet access. When the planets “align” and your whole family has devices with 3G support, then by the will of fate you should choose this network. If you don't bother with all this, take GSM.

What equipment is needed:

• External antenna (sent to the base station to receive the signal);


• Repeater (a device that amplifies the signal and transmits it to the internal antenna);


• Internal antenna (provides signal propagation indoors);


• Cable 5D/FB (cable for connecting an external antenna to the repeater);


• Connector N111/5D (plug for cable connection).

Regardless of the type of network, the equipment set has the same components. This kit is suitable for an apartment and a small private house, such as a summer house. In such cases, one repeater will be enough to distribute the signal throughout the room. If you need to boost the signal on several floors or over a large area of ​​the room, you will need more repeaters.

Be sure to find out at what frequencies the network you have chosen operates, this is necessary in order to choose the right equipment. Also find out from the operator where the nearby base station is located or determine this using special mobile programs. In general, the antenna is installed where there is the best network signal on the phone.

If you do not have certain skills and knowledge in this matter, then it is better to entrust the selection and installation to professionals.

Installation

First you need to strengthen the antenna, depending on its type and installation will be carried out. Fastening is done using anchors.

As mentioned earlier, you need to find the side that will have the best signal. It is in that direction that the antenna will be directed. You can mount the antenna on a wall or. In addition, if necessary, you can even build a metal tower on which the antenna will be mounted - this good decision for country and cottage villages.

The next stage of installation is cable laying. To do this, make a hole in the wall and connect the cable to the external antenna. We lay the inner part of the cable indoors to the location of the repeater. To attach lugs to the ends of the cable, it is better to use the services of a specialist in the store.

Then we proceed to installing the repeater. It is attached to the wall using dowel-nails, and if it is a simple antenna, it is placed on a shelf. Next, the internal and external antennas are connected to the repeater. After this, we connect the repeater to the power supply, configure it, and are satisfied with high-quality network coverage.

When choosing an installation location, before starting all work, draw up an equipment installation diagram. There must be a separate outlet near the repeater, and take this into account when drawing up the circuit. The repeater should be located in the center of the area where the signal needs to be improved.

This video will help you visually familiarize yourself with the installation procedure and equipment for signal amplification: