How to set up a d link dsl 2640u modem. Login via web management

As soon as the box with the new modem is in your hands, check the package contents. The following must be inside:

1. As a matter of fact, the D-link DSL u2640 device itself.
2. Splitter (a kind of “tee” that will allow you to use the telephone channel not only for telephone communication, but also as an Internet conductor).
3. Power supply device.
4. Lan - cable (can be of any color, depending on the configuration: gray, blue or green)

In addition to this, you will have to buy a telephone cable, the length of which is easy to calculate - it is equal to the distance from the slitter connected to the telephone socket to the intended location of the modem.

After all the basic preparations have been completed, you need to make a connection: disconnect the telephone cable from the phone and connect it to the splitter through the “Line” input, and connect the included cable to the “phone” output and the telephone set.

The next stage is connecting the telephone cable we purchased to the router through the modem output of the splitter and connecting D-Link to the power supply network. Then connect u2640 to your computer via Lan cable and turn them on.

Login to settings

Once you have dealt with the “hardware” part of the issue and placed the D-Link DSL u2640 router in its rightful place, the final touches remain.

First, you need to reboot the router, resetting it to factory settings: to do this, take a pin/clip/needle and press the “reset” button located in the recess of the link body on the back side (near the power connector and the “sockets” of the Lan cable).
!Attention! In order to perform this step, the device must be turned on.

After the reboot has occurred and the indicator shows that the device is working again, you can proceed to configuration.

At this point you will need the following data (which is located on the D-Link DSL u2640 labeled “Default Router Settings”):

• Modem administrator login and password.
• Modem IP address.

Open a browser on the computer to which the modem is connected and enter the modem’s IP address in the address bar and press enter.

Open the browser, enter http://192.168.1.1 in the address bar

In the window that opens, enter your login and password information to gain access to setting up your router.

If you did everything correctly, a page will open in front of you that will tell you about the main statistical indicators of your device: device information, network information and DSL status information.

If the page opened in a foreign language, then in the upper right corner there is a language button, with which you can open the list and set the language in which you are most comfortable working.

Tip: change the modem access password as soon as possible, to do this, click on the “advanced settings” button and in the “system” tab select the “administrator password” button. Then, enter New Password and click on the “save” button.

Connection setup

Connecting to the Internet is possible using two methods - via wan and using Click’ n’ Connect. Let’s consider the second one, since it is easier for a person who has not encountered connecting to the Internet before.

Click'n'Connect

This method takes much longer than its counterpart, but is accompanied by tips that will help you avoid mistakes. Let’s start setting up our Wi-Fi router’s connection to the Internet by clicking on the Click’n’Connect tab.

Make sure there is a connection to the telephone network through the modem splitter. To do this, pay attention to the LED above the DSL input (it should be lit).

If the signal indicator does not light, check the contacts at each stage of its journey (telephone socket - wire to the splitter, wire to the splitter - splitter, splitter - wire to the D-Link DSL u2640 wi-fi router, wire to the router - router).

If it still doesn’t work, make sure that the telephone socket is connected to the communication network. If the indicator above the DSL input is lit, then click the “next” button.

On the next page you have to select the type of connection to be connected. To find out which of them is supported by your provider, contact them. After selecting the appropriate connection type, click on the “next” button.

In my case this is a PPPoE connection

In the windows that appear, enter the information received from the provider: login and password. The values ​​of VCI are 40, and VPI are 0. Click the “next” button on this page and the “apply” button on the next page. In the “connection setup is not completed” window, click “Ok” and check for access to the network using the “ping” utility (enter “ya.ru” in the address line). If the test is successful, your computer will have access to the Internet, for which you will be instantly congratulated. If everything didn’t go smoothly, then after a few minutes click on the “recheck” button - it should help.

Your next step is to save the settings and reboot the device. To do this, in the “system” tab (upper right corner, next to the “language” tab), select the appropriate button.

Wi-Fi setup

Distributing wireless Internet will make life easier for owners of various gadgets (smartphones, tablets, laptops, etc.). And our D-Link DSL u2640 makes it possible to deploy such a network: so let’s take advantage of this.

Select the “wi fi” tab in the “advanced settings” section. Then click on the “basic settings” button and start creating.

In the special fields you have to enter the following values:

• In the “enable wireless connection” box, check the box.

• In the SSID field, enter the name of your network - the one that devices will see when connecting to it.
• Filling out the “country” field should not cause you any particular difficulties.
• In the “channel” tab you can leave the value “auto”.

Then we go to the security settings of our wi fi network (located next to the “basic settings” button of the “Wi Fi” tab) and do the following:

• We select the encryption method with which data will be exchanged between your devices and the router.

• We come up with and write down a password in the appropriate window, entering it using wireless network you will be able to go online.

Click on the “change” button, saving the modem configuration. Finally, go to the “system” tab located in the upper right corner and select the “save” button. and reboot).

On this D-Link setup DSL u2640 completed. You can make it possible for multiple people to access personal computers to the Internet via Lan sockets, but you may need a router if their number exceeds free sockets. It is best to leave the router setup to a professional.

Other firmware version:

Found a typo? Select the text and press Ctrl + Enter

Not much time has passed since the points Wi-Fi access could be found only in very crowded public places, such as airports, train stations, cafes, restaurants and other establishments.

Then large corporations and smaller offices are gradually switching to Wireless Fidelity (Wi-Fi) so that numerous employees can simultaneously and without problems use the Internet.

And for several years now, Wi-Fi routers have been installed in ordinary houses and apartments so that all household members have the opportunity to connect to a wireless network. Therefore, this topic is relevant. Connecting a Wi-Fi router correctly is not a difficult task, but it is a responsible one.

Advantages of using a Wi-Fi router over a regular modem

Using a wireless network simultaneously with several devices (computer, laptop, netbook, tablet, smartphone and phone);

The presence of a single hybrid network that provides the ability to use the Internet anywhere in your apartment or office without the use of wires.

In this article we will look at connection and configuration Wi-Fi routerD-Link DSL-2640U. The model under consideration is designed for home use, as well as for small offices. Such a router will be quite enough to provide users with high-speed broadband Internet access. The advantage of this model is its low price.

Wi-Fi router location

In order for a Wi-Fi router to cover as large an area as possible in an apartment or house, it must be installed as high as possible for good distribution.It is advisable to place the device in the center of the apartment.
Interference in efficient work router can be determined by its location on system unit computer, or its signal may be distorted by objects obstructing it. For example, carpets, aquariums, indoor plants, etc.

Below is an example of how to properly place a wireless access point in an apartment or one-story house.

For a two-story house there will be this option.

Connecting a Wi-Fi router D-Link DSL-2640U

Step 1 . You bought a router, brought it home, unpacked it, and checked the contents.

The package includes: router, power supply, instruction disk, splitter, patch cord, telephone cable, documentation. This is a standard set required to connect to the Internet.

Step 2 . Now we need to connect the router to the computer. We place the router at a short distance from the computer, make sure that there is enough cable (in this model, the length of the patch cord is 60cm).

To make it clearer which cable to insert into which connector, let’s take a look at rear panel router.

1. Power cable;
2. On/off button;
3. There are two small buttons: WPS and Wi-Fi on/off;
4. 4 LAN connectors, for connecting 4 devices;
5. DSL Port. Telephone cable connector;
6. Reset button. Reset to factory settings.

In more advanced models you can also find USB port for a 3G modem, flash drive or even a printer.

Next, you need to connect the cables to the back panel of the router.

Connecting cables to D-Link DSL-2640U

A) Take the power cable and insert it into the Power connector number 1.

b) If you use telephone Internet (adsl technology), then you will also need to connect a splitter.

Splitter is a separator between the telephone line and the Internet. It is necessary so that you can use your home phone and the Internet at the same time.
The splitter connection diagram is shown in the figure below.

We insert the end of the wire that comes out of the MODEM socket on the splitter into the DSL socket on the router.

V) We insert one end of the patch cord into any of the 4 LAN connectors on the router.

We insert the other end into the LAN connector on the laptop or computer.

G) Turn on the router by pressing the On/Off button.

Step 3. Before you start setting up your router, we recommend resetting the settings to factory settings. Press the Reset button and hold it for 15 seconds.If everything is installed and connected correctly, then we can safely proceed to setting up wi-fi D-Link router.

Setting up a Wi-Fi router D-Link DSL-2640U

Connecting to WEB interface

Step 1 . Launch any web browser installed on your computer. Enter the router's IP address in the browser's address bar. (default 192.168.1.1) and press the key Ente r.

Step 2 . In the window that opens, enterUsername and Password administrator to access the D-Link router settings. Default Username - admin and Password - admin. Click the Login button.

Step 3 . If authorization is successful, the router settings window will open. Here you can find general information about the router and software.

Setting up an Internet connection

ADSL WAN connection

Step 4 . Open the tab in the left menu Network and select Connection.

Step 5 . On the right side of the window, click the button Add . A window will open for you to enter settings. In chapterspecify the name of the connection (can be anything) in the field Name . Specify the connection type in the drop-down list Connection type .

Step 6. In chapter specify the value of the identifiers VPI and VCI in the appropriate field. SelectEncapsulation methodfrom the drop down list.

Step 7 . For two connection types PPPoE or PPPoA fill in the fields PPP Username, Password, Confirm Password. After water press the button Save .

Ethernet WAN connection

Step 8 . Select tab from the left menu Advanced and click . If you are connected to the Internet via a telephone cable, then set the switch to No. If you have cable internet, then select any port, for example LAN1. Now you must connect your provider's Ethernet cable to this LAN1 port. Set the switch to the appropriate LAN port and press the button Save .

The D-Link DSL-2640U router is designed for home use, as well as for small office networks. It allows you to quickly and easily get broadband Internet access from one or more PCs, supporting Internet access speeds of up to 24 Mbps. Unlike the settings of other routers, dsl 2640u wifi setup differs mainly in that for signal transmission it is used not a LAN cable (using Ethernet technology), but a telephone cable (using DSL technology).

Before setting the parameters of our device, it must be connected to the electrical network and connected with a patch cord between the router and our computer. We insert one end of the cable into network card on the computer, and the other into one of the four LAN ports on the router. After making sure that the indicators are blinking, indicating that everything is in order with the connection, you can proceed with further configuration.

And first of all, we need to get into the interface of our device. To do this, launch your favorite browser and enter the following IP address there 192.168.1.1 and a window should appear asking for a login and password. Enter your login admin and the password is the same admin. If everything is correct, then we will see a configuration page for our device.

Setting up an Internet connection

Setting up the dsl 2640u router will begin with entering parameters for authorization on the Internet and obtaining full access. And so we had to get to the home page of the router settings, go to the menu on the left in the “Quick Setup” section. We uncheck the “DSL Auto-connect” box, since this function does not work 99% of the time.

After this, parameters will appear that need to be specified as follows: VCI is set to 35, for example, VPI is set to 0, but it is possible that your provider has their own. If necessary, check the QOS parameter (a function that allows you to reserve part of the channel for applications) and click the “Next” button.

On the next page, select your connection type. I hope that you checked it in advance with your provider, and also did not forget to find out your connection details. Most providers have PPP over Ethernet (PPPoE) and that’s what we choose. Click the “Next” button again.

On the new page you need to enter your data under the agreement with the provider, for PPPoE:

• PPP Username - user name;
• PPP Password - your password;

It is important to uncheck PPP IP extension, otherwise you will not be able to enable NAT and Firewall on the next settings page. Leave the remaining parameters untouched and click the “Next” button.

Now we enable the following parameters Enable NAT, Enable Firewall Enable, Wan Service (allows you to control the modem from the outside, if you don’t need it, don’t check the box). Service Name - you can come up with any name for the connection in Latin letters. And again click the “Next” button.

Setting up a local network

In the 2640u model, the wifi setup includes the following item - setup local network. In order for our computers home network had access to the Internet and to each other, you need to enable DHCP on the page that opens. To do this, enter the following data:

• IP Address: 192.168.1.1
• Subnet Mask: 255.255.255.0

• Start IP Address: 192.168.1.2
• End IP Address: 192.168.1.254

On the next page we will see data on our settings; basically, here we just press the “Save/Reboot” button. This completes the basic setup of the dsl 2640u router, but you still need to configure wifi.

WiFi setup

Now let's configure our wireless network. Go to the menu on the left in the “Wireless” section. Check the “Enable Wireless” checkbox. Enter the desired network name in the SSID field and click the “Apply” button. After the reboot we will have the opportunity to enter security settings.

One of the most popular devices today used to work correctly with the Internet, connected by the Rostelecom provider via telephone line, is a DSL 2640u router. And today we want to figure out how to connect DSL 2640u and how to configure it.

D-Link DSL 2640u modem kit

When purchasing or receiving a router, the first thing you need to do is check its contents. It is not extensive, and remembering all its elements is not so difficult:

• Power unit;
• Patch cord;
• Telephone cable crimped with connectors;
• Directly the router.

When you are convinced that the package is complete, you can proceed to the next step, which is to correctly connect and turn on the device.

How to connect D-Link DSL 2640u to Rostelecom

1. Connect the power supply to the modem.
2. Connect the telephone cable to the corresponding port of the modem and the other end to the corresponding port of the splitter.
3. Connect the patch cord to the router's Lan port and to the computer's network card.
4. Plug the modem into a power outlet.
5. Switch the device to the on state by pressing the corresponding button on it.

Equipment setup

Now that all the equipment is connected, you can start setting it up:

1. Launch the router’s web interface by logging in to page 192.168.1.1 in the browser using the username and password “admin”.
2. Press home page"Advanced settings" button.
3. Navigate to the “WAN” subdirectory located in the “Network” section.
4. If there are any parameters in the connection list, remove them. After that, click on the “Add” button, which will allow you to create a new connection.
5. Specify the “PPPoE” parameter in the connection type field.
6. Port select DSL.
7. Specify the connection name “Internet” to navigate available connections in the future.
8. Leave the VPI parameter at 0.
9. For the VCI field, enter 33.
10. The username and password are entered in accordance with the agreement with the provider.
11. The authentication algorithm remains in automatic mode.
12. The MTU item is set to 1492.
13. The LCP interval is set to parameter 30.
14. LCP failures – 3.
15. Enable NAT, IGMP and Firewall by checking the appropriate checkboxes.
16. Save your changes.

Setting up IPTV on DSL 2640u from Rostelecom

Of course, the setup cannot be considered complete until everything is working available services provided by the provider. Therefore, to bring it into working condition IPTV services, users need to add another connection in Network=>WAN. Its parameters are specified as follows:

1. Connection type – Bridge;
2. Port – DSL;
3. Name – TV. You can specify any name, but this parameter will allow you to navigate existing connections.
4. VPI is set to 0;
5. Enter VCI parameter 50;
6. The encapsulation method is specified by the LLC;
7. QoS parameter – UBR.

After entering all the parameters, click on the “Save” button again.

Setting up wireless access

And finally, of course, you also need to take care of the correct configuration of the wireless network, because today it is simply impossible to imagine Internet access in a home or office that cannot be connected to via Wi-Fi protocols. To this end, we perform the following actions:

1. In the main menu of the device’s web interface, go to the “Wi-Fi” section.
2. Select "Basic Settings".
3. Enter the access point name in the field
4. Check the checkbox to enable a wireless access point.
5. Save your changes.
6. In the “Security Settings” section, select the network authentication type WPA2-PSK, and also specify the access password to the Wi-Fi point.

This article will discuss step-by-step setup Internet, IPTV (also called Interactive TV), as well as wireless access using a universal router DSL 2640u Rostelecom. The named device is a modem that the company issues to new subscribers if they connect to an ADSL line.

Most of the time I write detailed instructions, and as an example I’ll take connections to a specific Rostelecom branch. In this material, the Krasnoyarsk branch of the organization will serve as an example. As for the settings for your region, they can be found on the service provider’s website.

Thanks to the described approach, you will be able to special problems configure a DSL 2640u modem in your region, because only the data in the VPI/PCI point changes, which, by the way, is publicly available.

Instructions for setting up a DSL 2640u router from Rostelecom

1. Go to the WEB interface of your modem.

Before entering the modem settings, make sure that each wire is connected correctly. To do this, you need to read the article on how to properly connect a telephone line to ADSL. If everything is good, then you can move on to the next stage. Now open any browser installed on your computer (absolutely any will do), enter in the address bar 192.168.1.1 , then press “Enter”.

At this stage, a window should pop up that asks for a username, as well as a password to enter the device interface.

Note. If your interface is not light, but dark (grayish), then this indicates that you need to update the firmware. The login and password to enter the interface remain standard - “admin”, “admin”. Of course, the quotes need to be removed.

Due to the fact that Rostelecom primarily uses a PPPoE connection, we will configure access to the network in this mode.

2. From the first menu, go to “Network”, and from there to “Connections”. To access the Internet, you need to create a connection by clicking “Add”.

“Connection type” select “PPPOE”, in this case the modem will not work as a router. If you want to use some other device as a router (which is probably more suitable in terms of technical characteristics), then select the “Bridge” mode (then the DSL-2640U will work as a kind of bridge);

3. It is required to register certain PVCs.

You need to write “VPI and PCI” that correspond to your subject for which you are setting up. If we take our example with the Krasnoyarsk Territory, then 0 and 35 are set. To get information about your region, just look at the relevant information on the website, you can also contact technical support on this issue;

4. Next, write down the “PPP name” - this is the login specified in the contract, “Password”, as well as “Password Confirmation” - everything is in the contract. It is best to write this information in text file to eliminate errors.

5. Make sure “Keep Alive” is enabled;

“LCP interval” should be set to 15, “LCP failures” enter 2 - this means that the device will send a couple of requests in a row for authorization to the server, and if the attempts fail, a new request will be made 15 seconds later. Those people whose DSL link on their modem often disappears should be set to 5 and 1, respectively;

6. Enable "IGMP";

Save the resulting settings. If you only need to set up Internet access, then you don’t need to read further. Just click on “Save” (top right).

If you also need to activate IPTV, then read on. For example, let's take the same router model.

To set up IPTV, you will need to create a couple of additional connections; set the mode to “Bridge”. Register the VPI and VCI of the region again - you already know where to get them. Click on the “Save” button.

For example, for Krasnoyarsk the value is paired (1/35, as well as 1/36), in this case it is necessary to create a pair of “Bridge” connections. Therefore, one more thing is added. When these parameters are not paired in a region, it will be quite simple to create a single connection.

It turns out that we have 5 connections (one of them is LAN, don’t forget). But that is not all! For good operation of the Internet and television, you need to create a group of interfaces. In other words, pass traffic from the TV into the LAN port, and leave access to the Internet in the remaining ports. It's easy enough.

7. Go to “Advanced”, then “Interface Grouping” and add a group.

Create your own group for television. “Name” - you can enter any name here. Move “LAN4” and a pair of “Bridge” connections from the column from left to right. Save the result.

The Internet will be in the first three LAN ports, as well as via WiFi, but TV will be in the remaining one. Click "Save and Reload" (located in the top right corner). After the reboot is completed, you can connect all the corresponding cables. Wait at least a couple of minutes so that the device has time to adjust to the new settings.

Setting up WiFi on a DSL 2640u modem Rostelecom

Go to “WiFi” 0 “ General settings" Pay attention to the SSID field; in fact, there should be the name of your network, which will be visible to those connecting.

After that, enter the “Encryption Key” (in other words, this is the password when connecting to the network). Enter and click “Save”. Also reboot the router and wait a couple of minutes. At this point we can assume that Rostelecom has been configured for DSL 2640u.

You can use the device to its full potential. If something still doesn’t work for you, contact technical support.